Tag Archives: FX5000

Yaesu DR-1X Repeater MultiMode Operation

Yaesu DR-1X Repeater MultiMode Operation.

The Yaesu DR-1X Repeater can be easily used for D-Star or DMR if you connect an MMDVM board to the rear accessories connector.

The Weston Repeater Group use four Yaesu DR1X’s as four of our five repeaters, and they work well and have done for years.
One is driven from a Wires-X box and is used as our Fusion repeater, two are in analogue ALLstar mode, one on VHF and one on UHF, but 2 are using MMDVM boards with no problem and run with Raspberry Pi 3’s, operating from Pi-Star SD cards.

Our fifth repeater is our D-Star repeater which uses a Simoco FX-5000.

All five repeaters then share the same antenna, which is nice!

To get the audio in and out of the rear 15w high density accessory socket and by-pass the filtered audio path between the RX and TX you will have to put the repeater into remote mode by grounding the appropriate pin on the accessories 15w rear connector. This is pin 1, which must always remain grounded.
Then make sure to use the CTCSS input pin rather than the audio input pin.
The correct pin is pin 6 ‘TONE IN’

All the pin-outs are in the manual.

I selected wide FM rather than narrow FM on the DR-1X so that the modulation was perfect from the MMDVM board, even though you would have thought that narrow would have been more suitable.

I have been caught out with the ‘remote operation’ selection wire coming off of pin 1 before and it does make everything very confusing because it sort of sounds like the digital signals are going through the repeater and into the MMDVM correctly, but in fact they are never getting to the MMDVM board, they are simply passing internally through the DR1X!
All very annoying when these things catch you out.

Amazon do some really nice break out PCB’s with the 15w connectors on them if you tire of soldering the buckets of the standard connectors.

The most important settings to get right in the Pi-Star configuration is to set the TX and RX invert to 1.

Then you need to realise that the TX deviation is very critical, and wider than you would first imagine on DMR.

I have set our DR1x to wide deviation to get the best modulation, even though you would think that you must use narrow.

We use Pi-Star on our raspberry Pi’s which drive MMDVM boards connected to Arduino’s.

If you are using different boards then you could find that your modulation sense is different to ours, and hence you will need to change the inversion settings.

Make sure that you have grounded pin 1 of the 15w socket on the rear of your repeater to put it into remote mode!

Make sure that as well as grounding pin 1 on the 15w rear socket of the repeater, do not use the AF IN pin 7 for your TX audio into the repeater. You must use pin 6 ‘TONE IN’ as this is the unfiltered audio input.
I hear of people using the AF IN pin all the time, but it will never work properly.

As far as RX audio goes, you obviously do not use the AF OUT pin 9, you must use the DISC OUT pin 8, which is unfiltered audio.

With the repeater set to wide FM rather than narrow FM it will all work perfectly.

On the touch screen of the repeater, you need to set the mode of the TX and RX to FM, rather than auto or digital.

You can force the repeater into this mode without touching the screen by setting pins 11 and 12 to the correct logic levels.

Pin 11 should be set low and pin 12 should set high to force the repeater into FM on TX and RX.

Good luck.

Owl February 2016

 

GB3WE 5 GHz Dish & 2.4 GHz Tonna

Join our Yahoo Group today!

Keep up to date and fully informed by joining our Yahoo Group: it-is-wb-we-subscribe@yahoogroups.co.uk

https://uk.groups.yahoo.com/neo/groups/IT-IS-WB-WE/info

 

The only place to find out what is going on with our repeaters is at our Yahoo Group: ‘IT-IS-WB-WE’ so do join today and don’t miss all of the latest news!

 

 

GB3WE 5 GHz Dish & 2.4 GHz Tonna

GB3WE Antennas June 2014

GB3WE Antennas June 2014
5 GHz omni
5 GHz dish
2.4 GHz omni
2.4 GHz Tonna
GB3WB 8 Stack
GB3WE Folded dipole


GB3WE Woodpecker

GB3WE Woodpecker

GB3WE Woodpecker


GB7WB Fan Control Thermostat Modified & Fitted

GB7WB Fan Control Thermostat Modified & Fitted.
The thermostat we had only had a ‘normally-closed’ contact and we needed a ‘normally-open’ contact to put the 24v fans on when ever the repeaters got too hot.
With three FX5000 repeaters stacked on top of each other, with their six combined crystal ovens and three power amplifiers etc you would be surprised just how hot they get!

A grub-screw was removed which was fitted to provide a rest for the center contact of the bi-metalic strip. A small screw with a solder-tag and wire was used to replace the grub-screw and the wire was attached to the spare solder post.

Now we have a single-pole, double-throw set of contacts and the fan switches on when the temperature rises.

GB3IE FX5000 Dual-Mode D-Star GMSK ircDDB Gateway & FM Repeater On Test

GB3IE Dual-Mode D-Star GMSK & FM FX5000 Repeater

GB3IE Dual-Mode D-Star GMSK & FM FX5000 Repeater

The Weston Repater Group recently completed a new dual-mode D-Star GMSK ircDDB & FM repeater for Plymouth. GB3IE is now on test in Plymouth, and will hopefully be in full dual-mode service very soon when its new NoV arrives.

GB3WB GB7WB & GB3WE Now All Using FX5000 Repeaters

GB3WE GB7WB GB3WB FX5000's

GB3WE GB7WB GB3WB FX5000's

All of our FM analogue and D-Star GMSK DV-RPTR repeaters are now using FX5000 base-stations.