GB3WE VHF repeater now an ALLstar analogue FM repeater

All five of our VHF and UHF analogue and digital repeaters are on air and working at the moment.

As with most repeaters we do suffer from a very few idiots intent on spoiling the repeaters for everyone.
Please ignore these trouble making people and do not reply to them or acknowledge them in any way.

We have a new project under way to allow us to pin point the exact location of these people and block them from accessing our repeaters.

We urgently need help to raise funds to buy the new hardware to enable us to keep our repeaters on the air and free from trouble.

We will be able to easily produce maps showing the exact location of any trouble making transmissions, which will be used as evidence when reporting and helping to take these people off air.

It is now Monday, May 25 th 2020 and we still need your support.

If you can help with a donation so that we can keep all our repeaters on air, then please use the PayPal donate button on this site or use the contact form so that you can use bank transfer or meet up with us.
Any amount will help!

bank details:


Please enter your callsign or name in the reference box when you use a bank transfer.

Please email us once you have made a bank transfer and include your callsign so that we know who has made payments to us. Send your email to:

Thank you

People who have sent donations for the new DF system:

M7DMS Dave
G8NQO Alex
M1OOO Iain
2W0CGM Nigel

MW6OIV Robert
G4UPR Melvin
G3SDH Paul
M0RSJ Keith
MW6RQC Robert
2W0ZBC Glyn
M6NQJ Andrew
G7RPG Peter
M0HZE Philip
G0KJF rick
2E0RLZ Simon
G0UQT Steve
G7AIS Geoffrey
M0HZE Philip
GW0UXJ Ashley
GW0MTI Malcolm

Here are some photos taken via the repeater site CCTV of the GB3WB Buzzard who has lived at the site for years.
These were taken on Saturday 9th December 2017.
[masterslider id=”20″]
[masterslider id=”19″]

GB3WE VHF repeater now an ALLstar analogue FM repeater!

You can now talk World wide via the ALLstar network using your VHF FM radio.

We are connected to HUBNet which is a very busy network.


M0HOY HUBNet Monitor

ALLstar Network

The repeater is controlled by a tiny raspberry pi 3. This handles the ALLstar connectivity as well as the courtesy tones and logic.

You listen on 145.6875MHz
Use a -600 KHz Split
94.8Hz CTCSS
You transmit on 145.0875MHz

Our UHF FM repeater GB3WB has the same raspberry pi 3 ALLstar system fitted.

You listen on 433.300MHz
94.8Hz CTCSS
+1.6MHz Split
You transmit on 434.900MHz

At the end of each transmission or ‘over’ the analogue repeaters will send one of three CW (morse) letters.

They will send an ‘L’ (.-..) if the last user was a local RF user and the repeater is connected to the ALLstar network.

The repeaters will send an ‘I’ (..) if the last signal was originating from the Internet.

The repeaters will send a ‘U’ (..-) if they are not connected to the ALLstar network and the last user must have been a local RF user.

GB3WB automatically disconnects from ALLstar at 21:15 until 22:15 every night to allow the repeater to be used for a regular net which is run from the Cardiff area and this net has become a great part of GB3WB.

When ever using the ALLstar network please always leave a four second pause between transmissions as this allows the nodes and repeaters to reset. This four second gap also allows others to break into the conversation.

Our two Allstar repeaters are connected to the HUBNet UK network.

Please get in touch using our contact form if you think that any of our 5 repeaters are not working.

Leave a Reply

Your email address will not be published. Required fields are marked *